Omnio flush mounted push-button interface 2-channels TST230/12
The Omnio flush mounted push-button interface 2-channels TST230/12 is a binary input device to integrate wired push-buttons, switches and sensors into the Omnio radio system. One potential free and one non-isolated 230 V~ closing contact may be connected to its inputs. Depending on the chosen evaluation (rocker-switch, push-button, time switch or weather station) the push-button
Omnio Room Sensor RTF160
The Omnio room sensor RTF- 160 is a battery less, maintenance-free and wireless sensor to measure temperature (0…40 °C) and humidity (0…100 %rH) indoors. The measured value is transmitted wireless to Omnio thermostat actuators and gateways. The RTF160 is characterised by its excellent long-term stability and thanks to the built in solar cell it is
Omnio flush-mounted multi switching actuator 2-channels UPS230/12
The Omnio flush-mounted multi switching actuator 2-channels UPS230/12 is a device for switching electrical loads. Its two potential free outputs are able to be actuated from up to 50 Omnio radio transmitters. Each transmitter can be programmed with one out of twenty different functions such as switch, push-button, staircase lighting, step-switch (AW20), time controlled switch
Omnio weather evaluation unit XFJ
The Omnio weather evaluation unit XFJ is able to convert the captured weather data into EnOcean telegrams. This way blinds can be pilot-controlled and protected against thunderstorms. The following individual signals are available: Channel 1: Weather raw data for higher-level systems according to EEP A5-13-01… 06. Channel 2: Alarm due to failure of the weather
CO2-Sensor
The CO2-sensor is a wired radio sensor to capture the concentration of carbon dioxide (400…2550 ppm) in the air. The measured values are transmitted wireless to Omnio gateways. It is particularly used to control the air quality indoors in offices, schools, hotels and residential premises. EnOcean Equipment Profile (EEP) A5-09-04.
Omnio blind cable actuator 1-channel KXJ230/12
The blind cable actuator 1-channel KXJ230/12 is a device to control 230 V~ tubular motors of blinds, sun blinds, awnings, sliding gates or garage doors. Its two interlocked outputs are able to regulate one drive and can be actuated from up to 50 Omnio radio transmitters. This allows the exact positioning of the blinds and
Omnio DIN rail mounted blind actuator 4-channels REGJ12/04
The Omnio DIN rail mounted blind actuator 4-channels REGJ12/04M is a device to control 230 V~ tubular motors of blinds, sun blinds, awnings, sliding gates or garage doors. Its eight potential free interlocked outputs are able to regulate four drives and these can be actuated from up to 50 Omnio radio transmitters. This allows the
Omnio flush-mounted blind actuator 1-channel UPJ230/12
The Omnio flush-mounted blind actuator 1-channel UPJ230/12 is a device to control 230 V~ tubular motors of blinds, sun blinds, awnings, sliding gates or garage doors. Its two potential free interlocked outputs are able to regulate one drive and can be actuated from up to 50 Omnio radio transmitters. This allows the exact positioning of
Omnio universal cable dimmer 1-channel KD230/10
The Omnio universal cable dimmer 1-channel KD230/10 is a device for dimming LED luminaires and other electrical loads. Thanks to automatic load recognition (R/L/C) the dimmer selects the right operating mode as well as the ideal dimming curve for the connected light source. Up to 50 Omnio radio transmitters can be programmed. Each transmitter can
Omnio flush mounted universal dimmer 1-channel UPD230/10
The Omnio flush mounted universal dimmer 1-channel UPD230/10 with extension input is a device for dimming LED luminaires and other electrical loads. Thanks to automatic load recognition (R/L/C) the dimmer selects the right operating mode as well as the ideal dimming curve for the connected light source. Up to 50 Omnio radio transmitters can be